Gyproc Plasterboard Patches various sizes 12 Pack (2 x 50mm, 5 x 100mm & 5 x 150mm))

Product Information

Once the adhesive has dried enough to support the patch you can now push the screw out into the wall void. Leave for a further 24 hours for the adhesive to completely harden off and then you can start filling. Due to the nature of plasterboard and in a similar way hollow doors, they can become damaged quite easily. As you will need to do a bit of cutting, before you start this, firstly run over the area around the hole with a wire detector to make sure there aren’t any wires, pipes or other items that you may accidentally cut through. Artex Caulker (250mm ) helps to fill joints and create smooth finishes or any suitable jointing knife Apply the filler by working it into the holes of the patch and towards the edge. Feather out at least 50mm beyond the edges of the patch to create a smooth, seamless finish. Leave to set for a minimum 30 minutes.

Remove any loose bits from the edge of the hole or damaged area, and sand this down. Remember to always wear eye protection when sanding.Another way to fill a hole in plasterboard is to enlarge the hole first to make a square of a suitable size. Then cut two battens (19 x 38mm timber will suffice) and make sure they are 100mm longer than the size of the square you have cut.

Gyproc EasiFill 20 has a working time of 20 minutes and the second coat can be applied after 40 minutes. Gyproc EasiFill 45 has a working time of 45 minutes and the second coat can be applied after 80 minutes.Finally, always follow the paint manufacturer’s recommendation, apply a primer or sealer before decorating. Now draw two lines across the gap to create a rectangle around the hole. Cut out the existing plasterboard with a sharp Stanley knife or use a small jab saw. Caulk can’t really be sanded down so you need to get it as smooth as possible. For any larger holes you are much better served by a more suitable filler. How Do You Fill Screw Holes In Plasterboard? The two main repair methods can be found below: Repairing a Plasterboard Hole Using a Piece of Plasterboard or Timber Now you need to measure and cut two noggins (horizontal wood that bridges the gap between the studs). Use a bit of 2 x 4 inch – approximately 100mm x 50mm – timber to create the noggins. Nail or screw them into position, between the studs, from the sides. This will create an area to fix your new plasterboard patch to.

With the batten positioned screw it in place through the front of the plasterboard making sure the screw heads go below the skim of plaster on the board. Do this with both battens and then cut a square of plasterboard to fit in the hole. This can be screwed to the battens with drywall screws and the square plastered together with the 4 screw holes for the battens. Depending on the shape of the hole, whether its circular or has jagged edges you may need to use a padsaw, jabsaw or hobby knife. Be careful using any of these items as they are sharp and can slip quite easily. To repair a hole in a hollow door, wall, or ceiling, firstly trim the edges of the hole and make is square. Ironically, you actually have to make the hole larger before you can go about fixing it! Picture the scenario. You have a job list as long as your arm, but you’re seeking efficient solutions for your customers, saving you time but not cutting corners.Add as much filler as you need to until the hole is filled flush with the surface of the wall. Use the trowel to get the surface as flat as possible.

Time saving and mess free compared to traditional methods of filing a hole with newspaper and building up layers with filing compound

Once the Gyproc EasiFill is fully dry, you may see darker patches – this is where the product is chemically set before it air dries. Once painted, these will completely disappear. It’s always good to finish by giving the entire area a light sand for a perfectly, smooth finish. Use a digital stud detector to locate studs, noggins and joists in walls and ceiling (Image credit: Getty Images) Can I Use Caulk To Fill Holes? Spread a small blob over the hole and wait for it to dry. Once dry, get a 180-220 grit sandpaper and rub down until smooth and blended with the current surface. How do You Fix a Hole in Plasterboard on the Ceiling? Measure and cut a new piece of plasterboard to fill the hole. Fix in place with plasterboard screws or nails. Mix up plaster, apply and leave to dry. Plasterboard is quite soft and the slightest of impacts such as when moving furniture can mark the surface and even put a hole right through it. The same can also be said for hollow doors – Due to the void in the centre and MDF or fibreboard used as the covering, this does not provide much protection when it comes to resisting impacts.