Creality Ender-5 Plus PEI Magnetic Flexible Heated Bed, 3D Printer PEI Printing Plate 377X370X2mm

Product Information

Better Bed Adhesion:Customized material PEI makes your print easy to adhere and has a wide compatibility of filaments, the magnetic Base with adhesive, so you can heat your bed to high temps for specialty filaments and not worry about the loss of performance.

Besides the larger volume, the Ender 5 Plus also includes a BLTouch auto bed leveling sensor and an end-of-the-filament sensor. The use of double sides spring steel sheets is not recommended as it reduces the magnetic pull and reduces the friction between the steel sheet and the printer bed. The Ender 5 Pro, with its stable, box-framed form, has outer dimensions of 440 x 410 x 465 mm (X-Y-Z). The size was inherited from its predecessor, the Ender 5. The addition of a 4.3” touch screen is a big improvement, making the user interface feel more direct and natural, and allowing more eyes on setup, jogging, and operation.Durable: The steel plate is made of high quality stainless steel, which has good flatness and durability. Hardware included - We include the required hardware for mounting the bed, build surface stop screws along with the thermal fuse and earth ground mounting screws. As an added bonus, it’s easy to clean: You can use isopropyl alcohol or wash it with warm water and soap for bigger messes. Extruder Arm: this add-on shortens the Bowden extruder to lighten the weight of the direct extruder on the moving components.

And they didn’t skimp on height, either — increasing from 300 to 400 mm. In some ways, that’s a more substantial change than the bed size jump. Flexible and removable: Can be slightly bent to pop off the prints. It is convenient especially for prints with large area. The pei is a little thin, please mind the distance between nozzle and surface to avoid scratching it. The Creality 3D Ender 5 is an FDM 3D printer kit. It uses Fused Modeling Technology, an additive manufacturing method that consists in melting a filament of thermoplastic and depositing it layer by layer in a pattern. The filament is pushed through a heated single extruder via a Bowden feeder mechanism. The tight entry of the Bowden tube makes it difficult to insert the filament into the route. Cutting the consumable in a steep angle might facilitate the task. With Ender 5 Pro, you can print in 220 x 220 x 300mm bed size. The Ender 5 Plus is larger in size and offers a bed size of 350 x 350 x 400. In terms of print volume, the Plus variant of the Ender 5 beats the Pro. What Is The Bed Size Of Ender 5 (Pro/Plus)?While this oversight on Creality’s part in this day and age is perplexing, you can turn the Ender 5 Plus’ motors whisper-quiet with a mainboard upgrade. Build surface locating pins - When using a magnetic build surface, our locating pins (screws) aid you to placing the removable build surface, every time. CR Touch Pre-Installed: Creality Ender-5 Plus 3D printer with CR Touch as configured. You just plug them in and start printing! It can precisely measure the tilt of the Bed surface, offers automatic compensation for the Z-axis for unevenness of the platform plate, easy to solve the printing failure caused by the unevenness of the platform and provide reliable operation with all build surfaces. Some guides recommend using a piece of paper to z-home and lower the nozzle until it is just barely low enough to grab the paper, but it still slides. I found that I needed to just barely grab like the advice, but then remove the paper, then hit Z- one more time which would have pinched the paper to where it could not move. You can fine-tune this during printing by tapping "Adjust" and then hit Z-. Changing this in the active print Adjust menu is permanent so when you find the right offset during a test print, it will be saved for the next print.

The device sports an industrial circuit board, which grants stable performance and high-load safety inspection. Also, it enables continuous printing for over 200 hours. Likely in recognition of changing market expectations, the Ender 5 Plus made a big leap in table size — to 350 x 350 mm, making an altogether bigger and more imposing machine. Thermal fuse and earth ground mounting locations – Additional threaded holes that provide a location for mounting a thermal fuse and earth grounding lead. Mainboard upgrade: Reduces motor noise, increases processing power, adds features like linear advance.An additional lead-screw on the Z-axis is another big improvement, stabilizing the drive and reducing the likelihood of build errors. The Ender 5 and Ender 5 Pro have only a single lead-screw that is made for a much less stable build platform. The heated platform lets you successfully print with PLA and PETG straight out the box. Even if showing some warping issues, printing with ABS and ASA is also possible. The Ender 5 is not a CoreXY 3D printer. Neither are the Plus and Pro versions. If you are looking for a Creality CoreXY 3D printer, you are better off looking at the Ender 6 instead. How do you make Ender 5 quieter? Ender 5 Plus will auto bed level, which is a big plus and brings the machine that much closer to plug-and-play. The Ender 5 shows an open-frame extruded aluminum cubic structure. When properly assembled, it results in a rigid and sturdy construction. The open design eliminates the risk of collision between the hot bed and the frame, an issue frequently encountered when printing with the Ender 3.

The tubing and fittings are also available as part of an all-metal extruder bundle from Creality, as we mentioned above, a cost-effective two-birds-one-stone upgrade. Their 3D printer enclosure traps heat inside, slows dust from accumulating on your printer, and acts as a sound damper. Additionally, this enclosure is made up of fire retardant material, which, in the event of your printer catching fire, won’t ignite and should stop the fire from spreading.The best Ender 5 enclosures provide a high and stable thermal environment protected from drafts and temperature fluctuations, precisely what these filament types require to thrive. If you prefer using a different slicer, you are free to do it. The open-source system of the Ender 5 makes it compatible with any type of free or paid slicing software currently available, including Simplify3D. Different software might not offer pre-set profiles for the Creality Ender-5. In those cases, you can manually add the data to create a custom profile. Bed support: composed of two support arms, this add-on has been designed to increase the print bed stability, reducing the risk of shifts in long-time printing. Magnet beds do not hold the spring steel print surface plate as well as an adhesive magnet sheet, this is mainly because you are holding smooth metal on smooth metal versus smooth metal onto a grippy plastic surface