Monument 2069 Compression Fitting Spanner, 24 x 32 mm

Product Information

The other way is to use a few turns of PTFE tape to the threads. Note that used this way the PTFE will not aid the sealing of the joint, but it will make the nuts easier to torque up. Compression fittings should be tight enough to create a watertight seal but not so tight that the pipe warps or the thread is damaged as this could encourage leaks and make the fittings much harder to remove later. Proceed with caution. What Should I Do if I Find a Compression Fitting Leaking?

Non setting lubricants and jointing compounds like that shown above can also be applied under and over the olive. This can be more effective for fixing leaks due to pipe scratches. Most tool kits will include a set of these. While not the perfect tool, they can be very useful since they will adapt to make a good fit on any nut. If you use them with the correct orientation they also grip harder the more force you apply to them: Once the nuts are done up hand tight on the joint, an additional half to three quarter turn with a pair of spanners (one on the body of the fitting to hold it still, the other on the nut) is usually adequate to make a seal. If the joint leaks, an additional tightening tweak will normally fix it. Note that over-tightening a joint may actually make it leak. Compression fittings are very reliable and have been proven over many decades, however sometimes things can go wrong and you end up with a joint that leaks. The common causes are:

Also means that you have twice the number of positions that the spanner can engage with the nut. This is very handy when there is very limited turning space for the spanner.

There is no significant difference. Compression fittings designed for liquid will work fine with gas but if you use optional PTFE tape, make sure it is gas grade. In addition, ensure the fittings are accessible and not hidden behind walls or under floors. Are Compression Fittings Reliable?An olive splitter takes a different approach by tighenting a sharp edge onto the side of the olive while supporting the pipe from the inside. They cut through one side of the olive without damaging the pipe, allowing it to expand a bit in diameter and slide off the pipe. The pipe needs to be cut square and cleanly, with any burrs removed. Pipes cut with a pipe cutter are much easier to use than those cut with a saw. The pipe needs to be clean and free from contaminants like paint or plaster etc. It does not need to be quite as clean and shiny as required for soldered connections. Slide the compression fitting olive (brass ring) over the first length of pipe, and then lay the nut over that Compression joints are designed to be used without any sealant. The nut compresses the olive driving it into the cone shaped profile at the end of the fitting body, causing deformation of both the metal surfaces of the olive and the pipe, zeroing the gap and creating a watertight seal.

The vice grip spanner is a combination of an adjustable spanner and a set of vice grip pliers (aka "mole grips"). Very handy for working at arms length in awkward spaces, and also for not marking polished chrome fittings like nuts on taps or service valves. They are very skinny which makes them uncomfortable to use as well, but sometimes this slimness is an advantage where there is not much space. Copper pipe works well with compression fittings. Chrome plated copper pipe also works well. Some advocate stripping the chrome from the area of the pipe in the fitting as this allows the olive to get a better grip on the pipe. There is no actual need to do this, but if not doing so, it is advisable to torque the nuts a little higher than with normal copper pipe since its harder for the olive to "bite" the chromed pipe. Sometimes an olive can be removed by tightening an adjustable spanner closely around the pipe, and then using it as a slide hammer to strike the nut or the olive itself and drive it toward the pipe end. Copper and brass olives both work fine. Olives can't be removed from a pipe and reused. Even hand tightening a fitting with an olive inside before the pipe is inserted, is enough to make the olive unusable.

Available in three sizes, 16mm – 40mm, 40mm – 75mm and 63mm – 125mm. This compact tool is a necessity for all your compression installations and repairs. Note that this may not cure a leak that is caused by a scratch on the pipe under the olive. You may be able to wind a couple of turns under the olive - but this is less easy. These are far better suited, are long enough to get good leverage and are comfortable to use. The design of the end wraps around more of the nut giving better support and greatly reducing the risk of damaging a nut: The partially "open" end allows the spanner to slip over a pipe, and then slid onto the nut. We are currently using Royal Mail Parcelforce and DPD as our delivery providers, all small items will be delivered by Royal Mail, these can take up to three working days to reach you.