Doctor Who - 12" Radio Control Dalek Thay

Product Information

Using a peace of strong corrugated cardboard the same size or larger than an A4 paper sheet, place the paper template on to the cardboard and use a pen to draw around it. Then cut around the marked edges of the cardboard using a craft knife and ruler (or a peace of straight wood) to help keep the edges nice and straight.

The 12″ Radio Controlled Imperial Guard Dalek was originally released in 2006 a Woolworth’s exclusive… 23 7 May 2008 12″ Radio Controlled Dalek Thay Using the cereal box cardboard, cut out 8 small slats measuring 6.5cm x 3cm, and 14 slats 8cm x 3cm. I should mention here that it wasn't until later after I painted them, I realized that 3cm's was a little bit too wide as photos of other Daleks have about 16 long, thinner slats and about 6 short ones, so feel free to play around with the numbers. With the measurements I used, I ended up using 4 short slats and 7 large ones, which at the end didn't look too bad.I used a Bluetooth sun visor car kit and my iPhone. The speaker was small enough to fit inside the inspection panel and didn't cause any obstructions to the tank turret which turns the head. I made a second battery compartment made from cardboard, attached it on the top of the turret, and placed the main battery in to it. I now used the original compartment I made to rest the speaker in to it (as seen in the second photo). Here I will show you how I made my scratch built Dalek using items I rescued from our recycling bin, a broken but functional radio controlled tank, and other bits and peaces I had laying around crying out to be used. I hope this Instructable will give you some inspiration to make your own Dalek, as I think we need more of these poor misunderstood creatures roaming around our own little planet (even though they are hell bent on controlling the universe). To attach the head, apply some blobs of grab adhesive to the top of all 6 of the PVC foam supports and rest the head down on to them, applying a little pressure downward, insuring the head is on straight and even all the way around, then leave to set.

Many years ago, the Daleks sent out thousands of egg-shaped Progenitors containing the genetic coding of the race, so that new Daleks could be created whenever necessary… 76 24 Jul 2010 Infrared Controlled Dalek Ironside All the wires for the lights and aerial should be connected and running through the center of every panel. You should have a good length of the center axle which will turn the head, poking through the top of the chest section. I should mention here that on a real Dalek, the ring section stays fixed to the chest section and only the actual head dome rotates. I went a little different with this as I didn't want the 4 wires coming from the eye stalk pulling to much on the housing, and I need room for the pulley system for the eye stalk. Before fitting, get the eye stalk and place it on your work surface the right way up (so your camera view wont be up side down) then with a screw measuring about 8 to 10cm's long, screw it in to the middle edge of the pivot (6 to 8 turns should do it), about 3/4 of the way up so the screw protrudes about 45 degrees facing up. This will be the counter leaver for the eye stalk. Then using a length of electrical wire, tie around the screw as close to the screw head as you can. Cut a little peace of duct tape and wrap around the screw and wire knot to stop the wire slipping down the screw. If you did think the support struts wouldn't be strong enough, When the grab adhesive fully sets, the outer panels will now strengthen the support struts making it nice and sturdy. Trust me, I'm a doctor (not The Doctor) ;-) Character Options’s 18” radio control interactive Dalek responds to spoken commands as well as having traditional radio control functions via a special multi-function control unit. With independent head, body and eye movement as well as multiple sensory inputs including touch, now you can control the ‘supreme being in the universe’ from the comfort of your living room...With the camera, it had 2 small PC boards, 1 with the on/off switch, charging port and battery, and the other connected to the camera lens and microphone. They were connected by 4 small wires with a small, plug which I had to cut and extend. If you decide to use a camera, please bear in mind that it will probably differ to the one I used, and the wiring may be different to what is mentioned below. One at a time, poke the bent ends of the wire in to the pilot holes, enough that the length of the wire sits above the pen shaft about 1cm, then add a small drop of super glue to each hole to secure the wire in place. (In the Photos, You will see a grey pen lid. I didn't use it in the end as the LED didn't illuminate it enough).

Continue to fix the rest of the struts starting with front middle one. Now the trial and error bit comes in here. You want the top plate to be as level as possible, so here you can alter the size of the strut using and taping up the tabs which will also help to center the top plate and keep the tube axle straight when it rotates. Finish off fitting the last 2 struts and when the glue is dry, simply use a pair of scissors to trim off any excess cardboard from the strut tabs so everything is flush with the top plate. A WORD OF WARNING just in case your not aware. Polystyrene and spray paint are not friends (As seen in the last photo). Now repeat the process, this time around the base just above the bumper. When the base is complete, go panel by panel adding the final two spheres (four on the two larger side panels), making sure they are evenly spaced down and across the skirt panels. Done. One little thing you can do now if you had to use more than one peace for the final layer, is to use a little more adhesive, put some on your finger, and rub over all the joins to eventually make it look like one peace . When finished, leave overnight.Many years ago, the Daleks sent out thousands of egg-shaped Progenitors containing the genetic coding of the race, so that new Daleks could be created whenever necessary… 119 13 Nov 2010 Remote 13″ Dalek Drone – Pictures / Video IMPORTANT NOTE. I placed the motor on a small length of wood with the newly made pulley wheel laying flat and below the motor cog. This was to prevent any excess glue running down the drive shaft and then seizing the motor. The 5″ Radio Controlled Supreme Dalek is available now. It featured in Two episodes from series Four… 4 7 Aug 2008 12″ Supreme Dalek